R&D in Hsinchu, Taiwan · Sales & support in Shenzhen
Home/Applications

Parts only matter once they land in a design

Lighting, security, automotive, industrial, consumer and telecom are where our volume goes. Each has a proven reference approach, recommended parts and known failure points.

Scenarios

Find the cell you are in

The same MOSFET is selected very differently in lighting and in motor drive. Confirm the scenario first — it saves half of the trial and error.

01 / GREEN LIGHTING

Lighting

Indoor LED bulbs and tubes, landscape lighting and large architectural lighting — the earliest and most mature market for KRN. Non-isolated buck, linear constant current and isolated flyback: we have parts for all three.

The usual pain points are electrolytic capacitor life at high temperature and MOSFET switching loss. Low-Qg MOSFETs plus molded inductors keep the temperature rise down.

Indoor bulb / tubeLandscapeArchitecturalWide inputLow rippleLong life

Recommended direction

  • LED constant currentPower management IC
  • Main switchN-channel MOSFET
  • Output rectifierSchottky diode
  • StorageMolded inductor
  • Input protectionTVS / fuse front-end
  • Driver supplyLDO
Reference designs and part lists can be tailored to your output voltage and current.
02 / SECURITY & SURVEILLANCE

Security

Cameras, recorders, alarms, video intercoms and TV-wall decoders — the real requirement here is running 24/7 without surprises: stable supplies, hardened interfaces.

PoE or 12 V rails, multi-rail buck converters, and ESD protection on Ethernet and audio jacks are the most common combination.

CameraDVR / NVRAlarmIntercom24/7 operation

Recommended direction

  • Multi-rail step-downDC-DC buck IC
  • Sensor / MCU supplyLDO
  • Interface protectionESD / TVS
  • PT motor driveMOSFET / driver
  • CommunicationRS-485 / optocoupler
  • Input filteringCommon mode choke
For outdoor units, confirm surge class and operating temperature range first.
03 / AUTOMOTIVE

Automotive

Lighting drivers, on-board supplies and body control modules demand far more in temperature, surge and vibration than consumer designs. Our role is usually to harden a consumer-grade approach for automotive conditions.

Automotive part numbers involve certification and validation status — always confirm the compliance documents of a specific part with us before design-in.

Lighting driverOn-board supplyBody control−40–125 °CSurgeVibration

Recommended direction

  • Constant currentLED driver IC
  • Load switchAutomotive MOSFET
  • ProtectionTVS / ESD
  • FilteringShielded inductor
  • MCU supplyLDO
  • IsolationCAN interface
Validation documents (PPAP / reliability reports) for automotive parts are available separately.
04 / INDUSTRIAL CONTROL

Industrial

Motor drives, industrial supplies, isolation and protection. Two things kill industrial designs: gate drivers blowing up, and supplies folding under surge.

Gate driver matching, MOSFET avalanche margin and TVS clamping on the bus are the three calculations we most often do with customer engineers.

Motor driveIndustrial supplyIsolated driveCurrent sensingHigh reliability

Recommended direction

  • Power stageMid-voltage MOSFET
  • Gate driveGate / isolated driver
  • Current sensingCurrent sensor
  • Bus protectionTVS / rectifier bridge
  • Control supplyDC-DC / LDO
  • Signal filteringCommon mode / bead
For high-current designs we support current sharing and thermal design reviews.
05 / CONSUMER

Consumer

Fast charging, power banks, small appliances and wearables — a balance of size, efficiency and cost, usually with a two-week deadline for samples.

Small molded inductors, low-Iq LDOs and 0402 ESD are the combination we use most for charging and wearable customers.

Fast chargingPower bankSmall applianceWearableSmall sizeFast samples

Recommended direction

  • Step-up / step-downDC-DC IC
  • ChargingLi-ion charger IC
  • StorageMolded inductor
  • Type-C protectionESD protection
  • Standby supplyLow-Iq LDO
  • Key / motor driveDigital transistor / MOSFET
Early involvement shortens certification and board revision cycles.
06 / TELECOM & TRANSPORT

Telecom & Transport

Telecom equipment supplies, traffic signal control and rail auxiliary systems. Long design cycles, strict validation, few changes — once designed in, a long-term relationship.

We typically enter at the secondary-side supply and interface protection, then support the customer through long reliability validation and lot consistency checks.

Telecom supplyTraffic controlRail auxiliaryLong-term supplyLot consistency

Recommended direction

  • Secondary rectificationSchottky / fast recovery
  • DC-DC conversionPower management IC
  • InterfacesRS-485 / CAN
  • Port protectionTVS / ESD
  • Filtering & storagePower inductor
  • Isolated sensingOptocoupler
Annual stocking and safety-inventory arrangements are possible for long-cycle projects.
How We Work

Where we show up, from selection to volume

We do not hand over and disappear. The later a project gets, the more it needs the supplier's engineers to still be online.

01

Selection & cross-reference

Send a part number or a spec, get a comparison table: differences, package compatibility, risks.

02

Samples

Stock parts shipped immediately; special ratings built to sample with measured curves.

03

Failure analysis

For an abnormal lot we help with mechanism assessment and cross-sections, then propose improvements.

04

Volume supply

Capacity and lead time locked, lot traceability and inspection reports included.

Project

Tell us the application conditions and half the solution is done

Input voltage, output spec, operating temperature, target cost — four numbers and we come back with something you can build.